Used TOTANI machines for sale

High-speed, side-weld, automatic bag making machine Total counter 3279 meters and only 52,011 bags made Roll to bag making machine Materials: OPP, CPP, HDPE, LDPE, LLDPE, and other heat-sealable plastic films. Film thickness: 20 – 100 µm. Max film width 900mm max roll diameter 500mm pin hole, adhesive strip for opening with removable sheet, plastic bags without gusset

FD-60DL68 HIGH SPEED BAG MAKING MACHINE with Transverse Direction EL-ZIP Applicator: Type I-500T/FD60V This machine can flat seal, gusset seal and 4 side seal pouches Film (Bag material): Laminated film Web size: Maximum diameter : 800mm Maximum width : 1,600mm Heaters and Coolers: Longitudinal heater No.1 : 1 set (640mm length/ 180mm width) Longitudinal heater No.2 : 1 set (640mm length/ 180mm width) Longitudinal cooler No.2 : 1 set (640mm length/ 180mm width) Cross heater : 3 sets (640mm length/ 60mm width) Cross heater : 2 sets (640mm length/200mm width) Cross cooler : 3 sets (640mm length/200mm width) Range of bag size (A) Bag without gusset Bag width : 200 to 450mm – 2 x Gusset Bag length : 000 to 600mm Gusset depth : 45 to 140mm Gusset depth : 30 to 140mm (without bottom punch) Production rate (A) Cycling speed : Maximum 150 bags/min. (without gusset) Maximum 100 bags/min. (with gusset) (B) Linear film speed : Maximum 45 meters/min. Range of Punch size (For Handle) :80mm x 140mm Range of Thomson punch size :¡:90mm x 130mm Electric consumption : Approx. 26Kw, Approx. 100KVA * Power source : 200V with +/- 10% allowance, 50 or 60 Hz, 3-phase Note: A transformer will be equipped. Water consumption : Approx. 10 liters/min. Note: Must be clean cooling water. Air consumption : Approx. 10 N-liters/min. of 6 kg/c ㎡ Note: If using notch or punch device, compressed air will be Moreover required approx. 15 N-liters /min per one.

Three Side Sealing (BH-60HV) with Standing Pouch unit so machine is (BH-60HVLLS) with crosswise simultaneous two-line printing rolls Finished pouch dimensions: Pouch width(feed length): 60 to 250mm Pouch height: 120-270mm Bottom gusset depth: 2-45mm (70mm) Bottom punch diameter: 12 to 20mm Film roll dimensions: Main film roll Max Diameter: 600mm (rolled on 3-inch pipe) Min Width: 1100mm Bottom Film roll Max Diameter: 600mm (rolled on 3 inch pipe) Min width: 150mm (2 shafts horizontal axis type for 2 line-pouch) Max weight: 40kg Film Speed: 25m/min Feeding width: 200-600mm Maximum feeding length: 500mm Unwinding Device Unwinding max diameter: 600mm (800mm is available under 30m/min film speed) Maximum width : 1240mm Automatic Tension control power brake device AC servo motors Plain films max. 180 shots/min Feed pitch: 165mm Printed film max. 180 shots/min Feed pitch: 145mm Longitudinal heater (feed direction) Effective sealing length: 600mm...5 units Longitudinal cooler (feed direction) Effective cooling length: 500mm...5 units Cross heater (width direction) Effective sealing length: 600mm...2 units Cross cooler (width direction) Effective cooling length: 600mm... unit Cross seal bar: maximum sealing width 80mm Longitudinal seal bar: maximum sealing width 50mm Power required : 29.5kW Longitudinal heater: 13.0 kW Cross heater: 9.6 kW Heater moving Servo Motor: 3.5 kW Film Drive Servo Motor: 2kW Unwinding Motor: 0.4kW Control System: 1.0 kW Compressed Air: 0.6 MPa Cooling water required : Approx. 3l/min Equipment configuration: 2 bottom gusset punches... 2units The standard punch diameter is 12 to 20mm. One bottom seal photoelectric sensor (reflexion type) One bottom film folding device (triangle plate type for 2-line operation) 2 bottom film unwinding device (with forced unwinding unit) 2 horizontal axis type bottom film roll sections One bottom film guide spatula (for 2 line operation) One point of point seal bar (one base, for 2 line operation) 1 Set of round corner punching tools and punching noch tools (more then 30 pieces)

Feeding width: 200-600mm Maximum feeding length: 500mm Unwinding Device Unwinding max diameter: 600mm (800mm is available under 30m/min film speed) Maximum width : 1240mm Automatic Tension control power brake device AC servo motors

Three Side Sealing (BH-60HV) with Standing Pouch unit so machine is (BH-60HVLLS) with crosswise simultaneous two-line printing rolls Finished pouch dimensions: Pouch width(feed length): 60 to 250mm Pouch height: 120-270mm Bottom gusset depth: 2-45mm (70mm) Bottom punch diameter: 12 to 20mm Film roll dimensions: Main film roll Max Diameter: 600mm (rolled on 3-inch pipe) Min Width: 1100mm Bottom Film roll Max Diameter: 600mm (rolled on 3 inch pipe) Min width: 150mm (2 shafts horizontal axis type for 2 line-pouch) Max weight: 40kg Film Speed: 25m/min Feeding width: 200-600mm Maximum feeding length: 500mm Unwinding Device Unwinding max diameter: 600mm (800mm is available under 30m/min film speed) Maximum width : 1240mm Automatic Tension control power brake device AC servo motors Plain films max. 180 shots/min Feed pitch: 165mm Printed film max. 180 shots/min Feed pitch: 145mm Longitudinal heater (feed direction) Effective sealing length: 600mm...5 units Longitudinal cooler (feed direction) Effective cooling length: 500mm...5 units Cross heater (width direction) Effective sealing length: 600mm...2 units Cross cooler (width direction) Effective cooling length: 600mm... unit Cross seal bar: maximum sealing width 80mm Longitudinal seal bar: maximum sealing width 50mm Power required : 29.5kW Longitudinal heater: 13.0 kW Cross heater: 9.6 kW Heater moving Servo Motor: 3.5 kW Film Drive Servo Motor: 2kW Unwinding Motor: 0.4kW Control System: 1.0 kW Compressed Air: 0.6 MPa Cooling water required : Approx. 3l/min Equipment configuration: 2 bottom gusset punches... 2units The standard punch diameter is 12 to 20mm. One bottom seal photoelectric sensor (reflexion type) One bottom film folding device (triangle plate type for 2-line operation) 2 bottom film unwinding device (with forced unwinding unit) 2 horizontal axis type bottom film roll sections One bottom film guide spatula (for 2 line operation) One point of point seal bar (one base, for 2 line operation)