Used TECNOVA Ø 105mm of 2003 for sale

Feeding silo for the grinded film Forced feeding hopper prepared for connection to the extruder Extruder 130/37 D with degasifier 185 KW direct current motor 6 heating zones Hydraulic screen changer, diam. 220 mm Frequency inverter Water head cutting. No. of blades 4, driven by a 4 Kw motor Tilting water/granule conveyor and screen for water/granule separation in stainless steel. Stainless steel mechanical centrifuge Centrifugal fan for granules launching, driven by a 1.5 Kw motor. Silo for pellet collection

Conveyor belt Grinder: 22kW Metal detector DC motor Filter diameter is 125 mm The cutting system has two stationary knife and three flying knife on the engine shaft. The mixing mill is Bruno Folcieri TAV.1.T.T.C. 400, weights of mill 1500 kg, dimensions with tape of 5950x1500 mm. The required working dimension for the plant is 8300x 9610 mm. Conveyor belt 15 m / m Silo capacity is 1000 kg Two screws: one engine 2.22 kW and another 6.75 kW with double throttle regulation. Silo engine motors and cylinder filler motors Heating zones: 5 1 zone: 9000 W 2 zone 9000 W 3 zone 9000 W 4 zone 9000 W 5 zone 9000 W Water consumption: 7 m3/h

Suitable for processing: PE/PP/PS 8mm diameter screen Humidity max 3 % Silo: capacity 2m³ Water head cutter Air cooling Venturi, cyclone and pipes Installed power: 30 Kw

Regeneration plant with water head cutting for PE/PP/PS 8mm diameter screen Print max. 50% - humidity max. 3 Film silo, capacity 2mc Forced feeding Extruder 60 LD 35 with degassing Vacuum pump for degassing DC motorization Temperature control panel Manual screen changer Pressure control Water head cutter Big bag holder Venturi, cyclone and tubes

REGRANULATION LINE WITH WATER CUTTING AT THE HEAD INPUT MATERIAL LDPE FILM, CLEAN AND DRY Printing percentage up to 50%, material humidity up to 3% SILOS 13 M3 made of carbon steel with forced material flow controlled by a 3HP motor,with Plexiglass material level control windows, loading cyclone with filters and dust sleeve FORCED FEEDING feeding hopper adapted to the extruder connection, screw pressure screw controlled by a gear motor with a 12.5 HP motor with an inverter EXTRUDER WITH DEGASSING frame made of welded steel, reducer without clutch, reinforced gears, hardened VACUUM DEGASSING PUMP 10 HP ring pump fitted with a tank for the monomer smasher AC MOTOR WITH INVERTER 280 HP AC motor, 400V 50Hz, with console and control panel with three-phase inverter maximum 280 HP TEMPERATURE CONTROL SCREEN WITH HEAT EXCHANGER with 6 electronic thermoregulators with double protection for the cylinder and 6 thermoregulators with single protection for filter changer and head - dust filters IP 45 HYDRAULIC SCREEN CHANGER BD PLAST filtration zone with a diameter of 220 mm This screen changer is the original one and has been working only one year. Now it is not installed but it will be installed before the delivery HYDRAULIC CONTROL UNIT to control the piston of the changer, accumulator with a capacity of 20l, pump controlled by a motor 7.5HP, oil tank capacity 120 l, max pressure 200 atm. PRESSURE CONTROL SCREEN fluid pressure control with diaphragm probe, dual protection levels - first audible signal - second extruder stop. WATERJET CUTTING ON 90°C HEAD VIBRATING SCREEN flat screen with two entrances made of welded steel, separating granules with holes with a diameter of 8mm, controlled by a 0.5HP motor dimensions 1400X500X900H Available automatic filter Cofit GB1000L (installed), price on request. Average power consumption: 250kW COOLING WATER DEMAND: 2200L/H