HITEMA - PS10.09
Air dryer. Air dryer HITEMA model PS10.09 Year 2010 Max pressure Freon side 28 bar Max. pressure air side 12 bar Refrigerant R407C 2,7 kg...
2010 | 300046532 | HITEMA
More information
Used Ancillary Equipment
Looking for a used Ancillary Equipment? Visit us to see our selection for sale!. Air dryer, Die Head for profiles, Heating and cooling unit for moulds and dies, Marking equipment, Melt pump, Moulds, Saw for profiles, Winder for flexibles tubes and profiles, Haul off for profiles, Mould and die cleaning equipment Hitema, Meweka, Thermal Care, Ungricht, Batte, Friul Filiere, Home Made, Lamp, Rossi Stamp, Baruffaldi, Baston, Hf Haytek, Lunardon, Mazzoni, Krauss Maffei, Maag, Pisko, Greiner, Bausano, Ciemme, Tamen
More information
MEWEKA
Die Head for profiles. Year of production: 2008-2012 Almost new, used only for test ONLY CALIBRATION TOOLING without table...
| 300038716 | MEWEKA
More information
THERMAL CARE - NQW08
Heating and cooling unit for moulds and dies. Accuchiller Water-Cooled Portable Chiller Model - NQW08 Nominal Cooling Capacity - 8 ton at 50°F LWT Voltage - 460/3/60Hz Tank/Pump Options - Tank & Pump Included Pump Size - 1.5 HP Pump Rotary Non-Fused Disconnect Switch - Rotary Non-Fused Disconne...
2019 | 300046576 | THERMAL CARE
More information
UNGRICHT - HS-356
Marking equipment. Inlet height 1240.00 mm Inlet direction right- left Profile height adjustment 5,0-50,00mm Engraved roller/diameter 228.60 mm Rubber-coated roller/diameter 229.40 mm Counter pressure + roller/diameter 228.60 mm Engraved roller/length 175.00 mm Rubbe...
2002 | 300045166 | UNGRICHT
More information
BATTE - MELT PUMP ZB-B-100CC BODY
Melt pump. Melt pump this equipment consists of 3 components, the body, drive system and plc control. - Codes: MAQEBENGBODY - GEAR PUMP - BODY MAQEBENGDRIVEN- GEAR PUMP - DRIVEN SYSTEM MAQEBENGPLC- GEAR PUMP - PLC CONTROLLER - The set was purchased in October...
2021 | 300046438 | BATTE
More information
FRIUL FILIERE - Moulds - For shutters
Moulds. Tool for Rolling shuter 37 manufactured by Italian co. Campanieri. (year 2013) Tool for Rolling shuter 38 mm and 55 mm manufactured by Italian co. Friull Filiere (year 2005 & 2007) Tool 38 mm fill with expanded PVC (that tool need to be repar...
2007 | 300040538 | FRIUL FILIERE
More information
HOME MADE - Souliotis Bros.
Moulds. Dies and calibrators for cable channels. Few operating hours. Its look like new without any wear out . The all tooling equipment include 10 sets for the following sizes 15X13, 20X13,20X20, 40X20,40X40,60X40, 80X40.The sets for 60X40 and 80X40 are ...
2004 | 300028682 | HOME MADE
More information
HOME MADE - for Booth - Beach Cabin - Kiosk
Moulds. Offer includes: - Profile extrusion moulds (co-extruded kit + wall profile kit) - a whole series of metal shelving and metal baskets - prefabricated structures made with those profiles (little house 28,8 MQ - bathing cabin + hexagonal kiosk 5 MQ) ...
2006 | 300044062 | HOME MADE
More information
LAMP - set of moulds for gutter/waterways for Air Conditioning
Moulds. Set of moulds for waterways/gutters for AC...
| 300045155 | LAMP
More information
ROSSI STAMP
Moulds. Year of production: 2003-2005...
| 300038708 | ROSSI STAMP
More information
BARUFFALDI - TG_TVS/300
Saw for profiles. Cutting unit under vertical and transverse base and with pneumatic carriage movement max. profile dimensions: Width = 532,2 mm Height = 10,5 mm...
2015 | 300042679 | BARUFFALDI
More information
BASTON - TMQ-P-586-S-300
Saw for profiles. ...
2010 | 300046775 | BASTON
More information
HF HAYTEK - HDC 110 DUAL ARM
Winder for flexibles tubes and profiles. Pipe material: HDPE Pipe type: smooth Pipe diameter: Ø50 - Ø110 Winder type: double The coil is secured MANUALLY by a strap machine using plastic tape Speed min/max (m/min): 15 (can be adjusted) Number of arms: 6 A: 350/1000 mm B: 600 mm D: In...
2019 | 300043258 | HF HAYTEK
More information
LUNARDON
Winder for flexibles tubes and profiles. Double winder LUNARDON 5-2700 for PE pipes in the range of Ø 63 - 125 mm...
2000 | 300045988 | LUNARDON
More information
MAZZONI - ONDA 900 PE6
Winder for flexibles tubes and profiles. included two tube guides for Ø16 and Ø20 (picture attached)...
2013 | 300046638 | MAZZONI
More information
KRAUSS MAFFEI - KV432-3
Haul off for profiles. Puller with cutter KRAUSS-MAFFEI - belt length 2500 mm - belt width 250 mm ...
1984 | 300042178 | KRAUSS MAFFEI
Sold
More information
MAAG - Maax 7
Melt pump. Melt pump MAAG Maax 7 General application information application area: Thermoplastics application medium: HDPE: High Density Polyethelene density: 0.75 kg/l permissible materials: No limitations (all materials are allowed) vapor pressure: unknown a...
1995 | 300046249 | MAAG
Sold
More information
PISKO - PC96
Mould and die cleaning equipment. Pisko PC96 PET preform neck crystallizer machine, year 2014 Output: 12 000 preforms/hour Working hours: 27000 hours Configuration: PCO 1810 neck finish Includes following auxiliaries: - Preform Feeding System - Unscrambler - Temperature Control...
2014 | 300040281 | PISKO
Sold
More information
GREINER - Set of moulds
Moulds. PVC window frame profile moulds - Producer – Greiner / Austria - Calibrator – two pcs x 230 mm - Vacuum downstream – 3 m. - Condition – excellent...
2006 | 300035397 | GREINER
Sold
More information
BAUSANO - T0800
Saw for profiles. For sheets/pannels...
2011 | 300044448 | BAUSANO
Sold
More information
CIEMME - Taglierina profili
Saw for profiles. Ci.Emme saw for profiles. + Tilting, inclueded in the price. Brand: Ci.Emme Year: 2004 Entry Disc Diameter: 25 cm Profile width: 12cm -Engine Brand: Ansaldo Three-phase asynchronous engine Power: 220/380v - 4.5/2.6 A - 50Hz ...
2004 | 300043098 | CIEMME
Sold
More information
HF HAYTEK - HDC 50
Winder for flexibles tubes and profiles. Pipe material: PE Pipe diameter: Ø16 - Ø50 mm Winder type: double Speed max: 30 m/min Number of arms: 6 Inner diameter min/max: 350 -700 mm Outside diameter max: 1520 mm...
2017 | 300045131 | HF HAYTEK
Sold
More information
TAMEN - Bobinador 600 L1
Winder for flexibles tubes and profiles. ...
2001 | 300045685 | TAMEN
Sold
More information
- Ancillary Equipment
- Air dryer
- Die Head for profiles
- Haul off for profiles
- Heating and cooling unit for moulds and dies
- Marking equipment
- Melt pump
- Mould and die cleaning equipment
- Moulds
- Saw for profiles
- Winder for flexibles tubes and profiles
- Co-extruder
- Complete downstream lines for profiles
- Complete plant for profiles
- Extrusion line for PVC profiles
- Profiles Carpentry
- Laminating and wrapping machines for profiles and panels
- Printing equipment for profiles and panels
- Profile machining center
- Single Screw Extruders
- Single-screw extruder for PE/PP
- Single-screw extruder for PVC
- Twin Screw Extruders
- Twin-screw extruder for other materials
- Twin-screw extruder for PVC