İkinci El Pouch makinesi: WATERLINE RITEBAG 900-S-LP 2006

Bilgi WATERLINE RITEBAG 900-S-LP

Referans: 300041085

Marka: WATERLINE

Yıl: 2006

Diğer özellikler:

RITEBAG 900-S-LP is designed for manufacture of flat pouches made of multi layer films and laminates.

Dimensions of the pouches shall vary in a wide range of:
- width 80 - 300 mm.

Dimensions accuracy of the pouches (tolerance): ± 1 mm.
Seal width shall be from 5 to 40 mm.
Seals shall be gas tight, have no wrinkles and pinholes.


Description of Materials for Pouches Making
The pouches shall be made of laminates and multilayer соехtruded films of the following structures:
ВОРЕТ 12 // РЕ 40…150;
ВОРР 20 // РЕ 40…80;
РЕТ 12 // Alu 9 // РЕ 40…150;
РЕТ 12 // РЕТ 12 // РЕ 50…150;
РЕТ 12 // РЕ / EVOH / РЕ 50…150;
Соех РЕ / РА / РЕ 80…130 ,
Соех РА / РЕ / РА / РЕ / PE 80…130,
Соех PE / СоРА / ЕVOH / CoPA / РЕ 80…150; Соех РА / PE / СоРА / ЕVOH / CoPA / РЕ / PE 80…150.
(PE – polyethylene; BОPA – biaxially-oriented polyamide film; BOPET - biaxially-oriented polyethylene terephthalate film; BOPP – biaxially-oriented PP-film; EVOH – ethylene-vinyl alcohol; РА – polyamide; СоРА – polyamide copolymer; Аlu – aluminium foil).
Dimensions of the film:
Film thickness: min – 40 µm; max - 250 µm
Thickness tolerance: max. + / - 6,5 %.

Film width:
RITEBAG 900-S-LP
max. – 920 mm (two reels operation)
max. – 1240 mm (one reel operation)

Reel diameter: max. 800 mm.
Core diameter: 152 mm.

Unwind Section
2 Reel Reception and Unwind Device 920 mm (max)
- rapid exchange device, with expanding shaft 6"
- powered film unwinding system, gearbox driver, controlled by the film dancer.


2 Film Tension Device
- double film follower, with pneumatically adjusted film tension
- linear analogue sensor for dancer position detection.

2 Edge Guide Device
- ultrasonic edge sensor mounted on micrometric adjusting rod +/-70 mm correction range.


1 Film Feed Synchronization System
- Nr. 2 Feed systems (upper-lower) driver by independent digital servo driver, fully programmable
- registration mark sensor mounted on micrometric adjusting rod.

Reel Reception and Unwind Device 1240 mm
- rapid exchange device, with expanding shaft 6"

Film Tension Device
- double film follower, with pneumatically adjusted film tension
- linear analogue sensor for dancer position detection.


Wide Folding Board
- Nr. 1 Board base 1240 mm, 60° folding angle.


Sealing Section
1 Longitudinal Sealing Station
- driven by independent digital servo drives, fully programmable
- Nr. 3 Sealing/cooling twin bars (left-centre-right) length 600 / 600 mm, width 100mm.

Stretcher Unit
- edge Sensor with stretcher devices
- pneumatic valves (proportional).

1 Feed system driven by independent digital servo drive, fully programmable single dancer for film tension control.


4 Cross Sealing Station
- driven by independent digital servo drives, fully programmable
- sealing bar length 900 mm, width 60 mm.


2 Cross Cooling Station
- driven by independent digital servo drive, fully programmable
- cooling bar length 900 mm, width 60 mm.

2 Punching Station
- punching bridge, with electrical and pneumatic connection for Nr. 5 punching tools.

Longitudinal Slitting/Trimming Station
- Nr. 5 Cutting unit mounted on connecting rod with axial coarse/micrometric adjustment
- Nr. 2 Motorized trim rewinding system (left-right).

1 Registration Mark Reading Station
- Nr. 1 Reading sensor unit.

1 Feed system driven by independent digital servo drive, fully programmable.

1 Cross Cutting Station
- cross cutting station with servo-drive Guillotine mounted on ball rails
- fully programmable cutting hub (start-stop points) and speed


1 Output Conveyor with Stacking Gate
- Nr. 2 Antistatic bars
- adjustable stacking gate for piling-up
- programmable speed/cycle for piling-up or fanlike feed of pouches
- length 1400 mm, Width 900 mm.

.Controls System
- Nr. 1 Industrial-PC with VGA graphic monitor and touch screen 12" (800 x 600 pixel)
- hardware and software for remote assistance through phone line.