İkinci El Pouch makinesi: WATERLINE RITEBAG 1200-S-LP 2006

Bilgi WATERLINE RITEBAG 1200-S-LP

Referans: 300041079

Marka: WATERLINE

Yıl: 2006

Diğer özellikler:

RITEBAG 1200-S-LP types shall be designed for manufacture of flat pouches made of multi layer films and laminates.

Dimensions of the pouches shall vary in a wide range of:
- width 80 - 300 mm.
Dimensions accuracy of the pouches (tolerance): ± 1 mm.
Seal width shall be from 5 to 40 mm.
Seals shall be gas tight, have no wrinkles and pinholes.

The pouches shall be made of laminates and multilayer соехtruded films of the following structures:
ВОРЕТ 12 // РЕ 40…150;
ВОРР 20 // РЕ 40…80;
РЕТ 12 // Alu 9 // РЕ 40…150;
РЕТ 12 // РЕТ 12 // РЕ 50…150;
РЕТ 12 // РЕ / EVOH / РЕ 50…150;
Соех РЕ / РА / РЕ 80…130 ,
Соех РА / РЕ / РА / РЕ / PE 80…130,
Соех PE / СоРА / ЕVOH / CoPA / РЕ 80…150; Соех РА / PE / СоРА / ЕVOH / CoPA / РЕ / PE 80…150.
(PE – polyethylene; BОPA – biaxially-oriented polyamide film; BOPET - biaxially-oriented polyethylene terephthalate film; BOPP – biaxially-oriented PP-film; EVOH – ethylene-vinyl alcohol; РА – polyamide; СоРА – polyamide copolymer; Аlu – aluminium foil).
Dimensions of the film:
Film thickness: min – 40 µm; max - 250 µm
Thickness tolerance: max. + / - 6,5 %.

Film width: RITEBAG 1200-S-LP max. – 1220 mm (two reels operation)
Reel diameter: max. 800 mm.
Core diameter: 152 mm.
Sealing temperature max. 250 оС.

Unwind Section
Reel Reception and Unwind Device 1220 mm
- rapid exchange device, with expanding shaft 6"
- powered film unwinding system, gearbox driver, controlled by the film dancer

2 Film Tension Device
- double film follower, with pneumatically adjusted film tension
- linear analogue sensor for dancer position detection

2 Edge Guide Device
- ultrasonic edge sensor mounted on micrometric adjusting rod +/-70 mm correction range

Film Feed Synchronization System with 2 Feed systems (upper-lower) driver by independent digital servo driver, fully programmable
Registration mark sensor mounted on micrometric adjusting rod.

Sealing Section
1 Longitudinal Sealing Station
- driven by independent digital servo drives, fully programmable
- Nr. 4 Sealing/cooling twin bars (left -centre-centre-centre- right) length 600/600 mm, width 60/100/100/60 mm
- sealing bars with pneumatic cylinder (pneumatic opening)
- Nr. 3 Pneumatic Cylinders for each sealing bar

1 Longitudinal Sealing Station
- Driven by independent digital servo drives, fully programmable
- Nr. 5 Sealing/cooling twin bars (left -centre-centre-centre- right) length 600/600mm, width 60/60/100/60/60 mm

- sealing bars with pneumatic cylinder (pneumatic opening)
- Nr. 3 Pneumatic Cylinders for each sealing bar.

1 Stretcher Unit
- edge Sensor with stretcher devices - pneumatic valves (proportional)

1 Film Feed (Central)
- Nr. 1 Feed system driven by independent digital servo drive, fully programmable
- dancer for film tension control

4 Cross Sealing Station
- driven by independent digital servo drives, fully programmable
- sealing bar length 1220 mm, width 60mm
- sealing bars with pneumatic cylinder (pneumatic opening)
- Nr. 3 Pneumatic Cylinders for each sealing bar

- 3 zones heating cartridges (300 mm/600 mm/300 mm).

2 Cross Cooling Station
- driven by independent digital servo drive, fully programmable
- cooling bar length 1220 mm, width 60 mm.

3 Punching Station
- punching bridge, with electrical and pneumatic connection for Nr. 9 punching tools.

1 Longitudinal Slitting/Trimming Station
- Nr. 9 Cutting unit mounted on connecting rod with axial coarse/micrometric adjustment.
- Nr. 2 Motorized trim rewinding system (left-right).

1 Registration Mark Reading Station
- Nr. 1 Reading sensor unit.

1 Film Feed (Front)
- Nr. 1 Feed system driven by independent digital servo drive, fully programmable.

1 Cross Cutting Station
- cross cutting station with servo-drive Guillotine mounted on ball rails
- fully programmable cutting hub (start-stop points) and speed.

Output Conveyor with Stacking Gate
- Nr. 2 Antistatic bars
- Adjustable stacking gate for piling-up
- programmable speed/cycle for piling-up or fanlike feed of pouches
- length 1400 mm, Width 1200 mm.

Controls System
- Nr. 1 Industrial-PC with VGA graphic monitor and touch screen 12" (800 x 600 pixel)
- hardware and software for remote assistance through phone line.