Used ABG machines for sale

Machine build to work right to left Web width 330mm QUIPMENT DESCRIPTION / FEATURES: Unwind • 700mm unwind, electronic web guide (edge guide sensor) splice table and web clamps, auto brake tension control. • Roll lift for 700mm unwind • Corona treatment Vetaphone Infeed nip drive section, infeed dancer. Semi rotary flexographic printing station with quick change cassette comprising stainless steel ink pan, pick up roller, ceramic anilox roller and reverse angle doctor blade. The station has auto pre-positioning and servo drive re-register • 2 x Coating Cylinder 19” (coating width 320mm) • 1 x Printing Cylinder 19” o Flexo plate = 1,70mm o Tape = 0,20mm • 1 x Anilox roller 400LPI (6,77cm3/m2) • 1 x Anilox roller 200LPI (11,8cm3/m2) • GEW air cooled UV curing unit 140w/cm • Hot air drying system Over laminating tower with waste carrier rewind Mid press dancer to allow full rotary coating Semi rotary die cutting station with 19” magnetic cylinder (18” maximum repeat). • Kocher & Beck Gapmaster Outfeed nip drive section, outfeed dancer. Waste matrix stripping (maximum diameter 600mm) Rewind • Scissor slitting including 5 knives and removable knife shafts • Back Scorer used for edge trimming the silicon carrier, which is then rewound with the matrix. • Single spindle rewind with variable tension control, 76mm air expanding shaft • label length counter with batch and pause facility • Second rewind shaft with 76mm shaft Specification Maximum web width 330mm Minimum web width 180mm Maximum repeat length 18” (457,2mm) Minimum repeat length 2” (50,8mm) Rewind max diameter 500mm

Flexo (varnish) station, GEW UV curing system, Die-cutting station, Hot-stamping, Cold Foil, Cold lamination, In-line corona treater, Web aligner, Rotary, semi-rotary and fully rotary system.

Machine with working direction from right to left Maximum material width 330mm Equipment specifications and configuration: Reel Feeder. - For reels up to Ø700mm diameter, with expandable pneumatic shaft Ø76mm. - Automatic tension control. - Programmable stop and speed reduction when the preset size is reached. - Automatic side material aligner, with ultrasonic sensor for edge guiding. - Includes adjustable table for reel joining, with pneumatic clamps. Rotary flexographic printing unit - Servo-driven rotary flexographic printing unit. - Includes cassette complete with ink cup; take-up roller; anilox and a cylinder for continuous coating. o 1 x Coating Cylinder 11" (coating width 320mm) o 1 x Anilox rollers 400LPI (6,77cm3/m2) - Hot air dryer. - GEW UV dryer 140w/cm. Traction nip and inlet dancer (semi-rotary mode). - Allows to separate tension zones. Semi-rotary die unit - Includes 152z magnetic cylinder - Includes servo motorized printed mark registration correction. - Standard distance between die and pressure cylinders 480 microns. Traction nip and dancer out (Semi-rotary mode). - Allows to separate tension zones. Scrap stripping unit - Section for die waste stripping. - Rewinder with Ø76mm pneumatic shaft and web breakage sensor. Rewinding unit with shaft in upper position. - Slitting module equipped with 5 knives/counter knives for scissor type slitting. o Lifting and separating of the knife and counter knife automatically at machine stop. o Includes traction nip to maintain tension independent of rewind. o Minimum distance of 15mm between blade and cutting blade. General Specifications: - Maximum material width: 330mm. - Minimum material width: 180mm - Minimum working repeat : 2" (50.8mm) - Max. working repeat: 18" (457.2mm) - Maximum rewind diameter: 500mm (500mm) - Meter counter, number of labels, batches and pause mode

Machine with working direction from right to left Maximum material width 330mm Equipment specifications and configuration: Reel Feeder. - For reels up to Ø700mm diameter, with expandable pneumatic shaft Ø76mm. - Automatic tension control. - Programmable stop and speed reduction when the preset size is reached. - Automatic side material aligner, with ultrasonic sensor for edge guiding. - Includes adjustable table for reel joining, with pneumatic clamps. - Motorized reel elevator Traction nip and dancer at the entrance (semi-rotary mode). - Allows to separate the tension zones. Semi-rotary hot foil stamping module. - Equipped with magnetic cylinder and use of 0.71 mm thick Rotometric "Uniflex" type flexible engraving plates and 0.95 mm rubber including double-sided adhesive. - Maximum / minimum feed: 457 mm (18") / 50 mm (2") - Automatic longitudinal registration by means of photocell, with respect to the pre-printing of the reel. - Foil feeder on 200 mm diameter reels and 25 mm pneumatic shaft. - Oil heating equipment up to 200 ºC. - Hydraulic and manually adjustable pressure introduction. Flexographic unit - Servo-driven flexographic printing unit (rotary and semi-rotary mode). - Includes cassette complete with ink cup; pick-up roller; anilox and one cylinder for continuous varnishing and 19" (152Z) printing plate cylinder. - Automatic longitudinal registration by means of photocell, with respect to the pre-printing of the web. - Hot air dryer. - GEW UV dryer of 140w/cm. Laminating module. - For use as: o Laminating with adhesive film without backing. o Laminating with adhesive film with backing o Laminating with non-adhesive film, applying the glue on the flexo unit o Calendering UV varnish avoiding "orange peel" effect, "high gloss" or "super varnish" type finishing o Cold foil stamping ("cold foil") - Film feeder and rewinder on 400 mm diameter reels and 76 mm pneumatic shaft. Semi-rotary die cutting unit - Includes 152z magnetic cylinder - Includes servo motorized printed mark registration correction. - Standard distance between die and pressure cylinders 480 microns. - K&B Gap master Traction nip and dancer at the exit (Semi-rotary mode). - Allows to separate tension zones. Scrap stripping unit - Section for die waste stripping. - Rewinder with Ø76mm pneumatic shaft and web breakage sensor. Rewinding unit with double shaft in upper and lower position. - Back-scorer slitting module with two knives for material regrinding. - Slitting module equipped with 5 knives/counter knives for scissor type cutting. o Lifting and separating of the blade and counter blade automatically at machine stop. o Includes traction nip to maintain tension independent of rewind. o Minimum distance of 15mm between blade and cutting blade. General Specifications: - Maximum material width: 330mm. - Minimum material width: 180mm - Min. repeat : 2" (50.8mm) - Max repeat : 18" (457.2mm) - Max. rewind diameter: 600mm (bottom) - Meters, number of labels, batches and pause mode counter

In-line Turret Rewinder with the option of closing finished rolls with a label Max. roll diam. 350 mm Max. web width 330 mm 4 Air mandrels 4 of 76 mm Max. web speed 100 mt/min with 25-38 mm diam. mandrels 150 m/ min with 40- 76 mm diam. mandrels Counter of labels and meters 6 web dividers (5 lanes) Touch Screen H.M.I. Auto roll eject mechanism Adjustable core stop Servo drive - closed loop tension control Hot melt adhesive core glue device completes with 5 transfer wheels Hot melt tail gluing device 4 glue wheels 4 web dividers Rotary web driver Air assisted turn bar 1000 mm diam. cantilevered braked unwind, integral reel lift. Electronic web guide with adjustabe splice table & pneumatic web clamps