Used LEMO INTERmat HT 1350.3 & GLOVEmat 1350.3 of 2021 for sale

Type of production : Double-Strength-Handle Carrier Bag with Inside Patch as Handle Reinforcement (hot melt) Unwind width : 1600 mm Max reel diameter : 1000 mm The machine has print repeat control & folding triangle. The machine is in very good condition and ready for production. It is equipped with glue hot melt system for the patch handle, not welded.

Glue patch handle bag Materials: LDPE/ HDPE Max/Min bag width: 650/280mm Max/Min film thickness: 30/90mm Side gusseting unit with depth of 90mm Unwinder with 1200mm rolls Web guide Patch: Type Kaiser, 90mm width, Glued Pneumatic Cutting Unit Wicket final position of bags Trim blower included Power req: 25 kVA/63A

Carrying bag width ranges: 220 - 600 mm Carrying bag height ranges: 300 - 740 mm Material types and material thicknesses: Bag film HD-PE 2 x 20 - 30 microns LD-PE 2 x 34 - 70 microns LLD-PE 2 x 30 - 70 microns Slip film: LD-PE 70 - 90 pm Glue consumption: < 3 g/m2 Unwinder FA-UA 1600/1200 Unwinding width: max. 1600 mm Film unwinding: max. 1200 mm take-up height above floor: 200 mm Equipped with: - Circumferential drive with frequency-controlled three-phase motor 1 AWP 1600 steel, unwinding shaft pneumatic clamping for steel and cardboard tubes clamping range-0: 74 - 76 mm max. reel weight to be loaded: 2150 kg manual winding shaft adjustment to control the web edge hydraulic/motorised reel lifting TA 1600/6 m Dancer unit for web tension and speed control FD 1600 Folding triangle for the production of a half tube Infeed width of the flat film web: max. 1600 mm BF 1600.1 Bottom fold insertion device, for one-sided insertion of a bottom fold bottom fold depth: 30 - 80 mm equipped with - Arrangement on folding triangle - Pick-up frame with spring-loaded folding wheel and spreading device - Charging of the bottom fold DKT 850 Hotmelt Reinforcing sheet application station for the production of handle-hole carrier bags with inner gusset sheet reinforcement Reinforcing sheet Preferential and perforating device VS 850 Servo for pre-welding the bottom fold GS 850 Servo Handle hole punching device, for punching a handle hole STW 850 Cut-off seam welding device, for producing a side seam with welding wedge and welding roller ST-DKT 850 / 600 , Pen stacking product tray for collecting and stacking carrier bags with grip hole Entire unit can be moved up and down pneumatically Servo-drive for wing arms synchronous to the indexing machine, adjustable during production 3 vacuum hubs with 8 wing arms each

Sealing and slitting width : max 1100mm Draw length min-max : 200-2200mm Web speed : 140m/min Mechanical output max : 125 cycles/min - 250 seals/min max Small reel winding width min-max : 150-500mm Small reel diameter max : 150mm Reel change without wrapper max : 20 changes/min Reel change with wrapper max : 18 changes/min Bag width (feed) min-max : 300-1100mm (in tandem operation) // 300-2200mm (with a sealing station) Bag height min-max : 600-1100mm Edge fold : 50-60mm Wrapper width : 30-100mm Drawtape width : 25mm, double fold (original tape width is 100mm) Drawtape reel diameter max : 800mm Drawtape thickness : 0.025mm, HDPE film The drawtape film has to be made of an HDPE film covered with a colour contrast to be picked up by a photo-electric cell. The drawtape film has to be made of new material, no regenerate. Hole diameter (drawtape) : 50mm Hole diameter (vent) : 4mm Material data : (see picture) This machine doesn’t have many hours of operation, it was always used as back-up to the main machine

The machine consists of: Main machine with delivery table for 1200 mm, punching device and package folding, film web guide, hot separation and original AWB 1600, as well as an additional AWB 1600. Machinen has been mainly used to produce side gusseted flat bags in 50µ, i.e. 4 x 50µ = 200µ HDPE. As HDPE manufacturer, rarely produced LDPE, but assume that LDPE can be welded even thicker. The side folding station is not included in the offer, but a second AWB 1600 is included in order to produce two lanes without separation. Bag width Max: 1300 mm; Min: 180 mm Thickness ranges: 9-150microns Unwinder 1600mm max roll width Pneumatic unwind shaft, 1000mm max roll diameter Final positioning of the bags: table Photoelectric cell control SPS control Power: 28KVA