Used BOBST NOVA D800 of 2020 for sale

Web Width 600 - 1250mm Material to be Handled (In Micron) BOPP 12-60 PET 8-60 BOPA 15-60 PVC Film 30-50 CPP 25-50 PE 40-120 Met PET 10-25 Met BOPP 15-50 Met CPP 25-50 Pearlized BOPP 20-40 Paper 35-120 g/m2 (From 100 to 120 g/m2 the Max. web width is limited to 1000mm due to web tension) Laminates 30-100 g/m2 Web tension range 3.5 to 35 daN Duplex Automatic Unwinder (Model 310 Air Shafted) Automatic high speed reel splicing, push-button controlled Core diam. - 152mm Max. core length 1300mm The unwinder can load 1 reel with diameter 1020mm and 1 reel with diameter 500mm at the same time, or 2 reels with diameter 800mm. Corona treatment from Rotomec with ceramic covered surface. Colour registration control - S5100 BOBST Viscosity controller-auto Turn bar for reverse printing at station number 9. Electronic Line Shaft

BOBST CL750 DUPLEX LAMINATION MACHINE: Set for solvent based solvent less and water based adhesives coating system. -Rotogravure including cold seal coating in register on pre-printed material. -Flexo (five rolls system) and solventless bicomponent mixer from VEA The total production hours hasn’t reach 15000 hours yet Mechanical speed max 450 m/min Web width min- max : 400-1350 mm Coating width max : 1325 mm Heating indirect by thermal oil with detecting/control of solvent concentration Idle rollers made of special anti-corrosion aluminum alloy Materials : Primary unwinder BOPP min 12 µm, max 50 µm PET min 12 µm, max 50 µm OPA min 15 µm, max 50 µm PE min 30 µm, max 200 µm NYLON CAST min 30 µm, max 80 µm CPP min 60 µm, max 150 µm Aluminium min 7 µm, max 20 µm Paper/Laminates min 40 g/m2, max 80 g/m2 Secondary unwinder BOPP min 12 µm, max 50 µm PET min 12 µm, max 50 µm PE min 20 µm, max 150 µm CPP min 20 µm, max 150 µm NYLON CAST min 20 µm, max 80 µm Aluminium min 7 µm, max 20 µm Paper/laminates min 40 g/m2, max 80 g/m2 Rewinder : Laminates max 250 g/m2 Simplex primary & secondary unwinder and Rewinder motorized drum with web edge sensor, shaftless type, bidirectional, Unwinders diameter 1020mm - max reel weight 1000 kg and dancer roll Safety check for reel locking. Bonding section composed of lamination pressure roller antistatic against heated stainless steel drum (equipped with 1 heating unit from Frigo, controllable temperature) and 1 cooling drum. Drying tunnel: Flat web passage, 2 ventilation chambers each with a length of 3 m, for a total of 6 m. It opens from the bottom side. Corona treater: Primary unwinder integrated corona treater from MERO, control through screen: reading and parameters setting. The corona unit is suitable for conductive and non-conductive materials. Coating unit: Sleeve type pressure roller, Solvent/fumes captured by fan and exhaust duct from the tie rod of the coating unit and through movable hoods. A- Trolley for rotogravure coating with Doctor blade and sleeve coating cylinder: - finished of turning (not engraved) - 1 sleeve/cylinder holder shaft complete with cones and bushings according to sleeve Bobst standard design. B- Solventless trolley equipped with software for the speed curve of machine: The supply includes a solvent-less trolley composed of: *1 solventless coating cylinder made of chromium-plated steel *2 metering cylinders made of chromium plated steel 2 heating units Frigo circulated by water: 1 for metering cylinders 1 for coating cylinder *1 rubber-covered transfer cylinder, sleeve type. Equipment for cold seal coating (register From Bobst, model Registron S5100 + INKING SYSTEM sleeve/cylinder holder shaft complete with cones and bushings) The equipment of cold-seal is different from the rotogravure equipment. Electric panels: 1 touch screen for each primary and secondary unwinders, rewinder and coating unit. 1 main control panel, with one touch screen 22” AC vector drives & motors and PLC by SIEMENS. Notes: Availability of spare parts and sleeves total of 33 rubber sleeves. Instruction book and manuals for auxiliary equipment and machine drawings are available.

Min. width: 1050 mm core size: 152 mm Substrates: (microns) BOPP: 10 to 50 PET: 9 to 50 CPP: 20 to 40 LDPE: 25 to 50 NYLON: 12 to 50 UPVC: 20 to 100 Vacuum: Evaporation Zone Operating pressure: 5.0 x 10.4 mbar Pumpdown time, clean dry and empty: 5.0 x 10.4 mbar in 5 minutes Ultimate pressure: after overnight pumping: < 2 x 10.5 mbar Winding mechanism: Max. winding tension: 538N Min. winding tension: 49N Min. Drum tension: 1291N Evaporation sources: Evaporator source type: Resistence heated intermetalic Number: 25 Evaporator size: 150 x 30 x10 mm Aluminium wire size and purity: 2.0 mm - 98.8 % pure Metallizing Data: Max. Deposition rate: 2.2 OD at 630 m/min 2.5 OD at 600 m/min Deposition uniformity: +/- 5% Dependent upon material and running speed

10 extended oven V3000; NO.02~09 V1750 oven Tension range 3.5 - 35 daN Heating method: steam Steam pressure 6 bar Twin-axis automatic unwinding unit (310 series) Maximum roll diameter 1020 mm Tension range 3.5-35DaN Automatic reel change with deflection function; top and bottom reel modes Inflatable cores: 3", 6" inches Inking system mounted on printing trolley Trolley 2 sets Cold sealant coating device 1 set (final unit) Automatic color overprinting system 1 set, pre-overprinting device provided by BOBST Printing quality monitoring system Inline quality inspection: AVT Ink viscosity automatic control system

Pick up end 2021 Machine has CE and ATEX certificates Materials - FOAM (LDPE + HDPE) 150 microns - OPS min 20 microns max 60 microns - PET mm 10 microns max 70 microns - LDPE suitable for printing min 50 microns max 60 microns - PVC min 20 microns max 60 microns - Laminates (OPP + OPP) min 60 microns max 80 microns - PETG min 20 microns max 70 microns Web width: 400-850mm Registration system Bobst Model Registron S5-100-E4 100% Printing Quality control and inspection system Printer web inspection video system Viscosity made by ROTOMEC Model 1660RT ink pump is pneumatic made by ROTOMEC Original cylinder insert trolley system Solvent based Ink with drying chamber 2V2500X Heating: indirect by steam (doesnt include water boiler) Characteristics of the steam : - steam gauge pressure at our users 8 bar - steam condensate discharge free flow Web direction left to right Chill rolls Mounted at full path outlet and mid path outlet (only for double hoods) with the following characteristics diameter 163 mm cooling water supply through central pipe. non rotary. with even distribution of temperature supply and drain on transmission side free water drain (non-under pressure) water flow rate 700 It/h DUPLEX AUTOMATIC UNWINDER/REWINDER (series 310v, shafted type) max. reel diameter 1020 mm (or the diameter allowed by the max reel weight) max permitted ovality :5 mm web tension range 3 to 35 daN max reel weight 1200 daN fixed arms splicing by overlapping in either direction automatic high speed reel splicing, push-button controlled under-base web guiding unit from BST turret rotation by self breaking AC motor max cores length 900 mm material: board real mounted with through shaft web tension by one regenerative AC vector motor for each reel axis min reel diameter tor automatic splicing: 350 mm Possibility to print on the reverse side of the web using web reversing bars no cylinders included