Used HERBOLD SZ 560-2 of 2006 for sale

Wet size reduction of pre washed, post consumer, pressed PET bottles Material type: PET Screen size: 12 mm Input humidity: dry Output : 2500 to 3000 kg/h with knives and screens in good condition and knives properly gapped Storage hopper with forced feeding Bunker infeed height: approx. 2210 mm Hopper infeed cross section: approx. 1800 x 2000 mm Drive screw(s): 3 kW / screw With 3 horizontally mounted feeding screws. (mild steel) Material will be fed load-controlled into the cutting chamber by frequency converters The entire unit is mounted on a movable frame. Rotor diameter: approx. 600 mm Rotor length: approx. 1488 mm Number of rotor knives: 7 x 2 Number of stator knives: 2 x 2 ran only approx. 2000 hours

Mechanical Dryer / Centrifugal Washer. Has only 100 working hours. Is sold since is not suitable for their process Screen basket diameter 900 mm Working length 1450 mm Screen perforation (standard) 2,5 mm Through up to (t/h): Rigid plastics 2,5, Films 1 Height with Open Mouth is 3,7m Can be used for Agricultural film , PET bottles , Battery boxes , HDPE material This unit can be used as a dryer or as an dry intensive washer. The mechanical dryers operate as a centri­fuge for film, regrind and mixed plastics. The wet fractions and the fines are mechanically dried in this centrifuged dryer and at the same time the contaminations are removed by the high impact energy and then will be evacuated. As an intensive washer, this unit uses a high volume of water to remove contaminates such as paper la­bels (pulp) from the fraction. For the washing of the flakes, there comprises a housing in which a special high-speed agitator rotates, a polygon shaped screen basket made from stainless steel, double outboard bearings, mechanical cleaning device for the screen surface pneumatically opera­ted with additional rinsing device. Models T 508-T 2015 (Rotor and housing is in mild steel, housing inside is special protected by 2K paint). Rotor wings at the ends are fitted with bolted wear plates. The feedstock that has contaminates or a high percen­tage of paper, an automatic mechanical cleaning scraper is used on the exterior surface of the screen drum. Special features: -Considerably higher drying efficiency due to an op­timized paddle-shape and position. Up to 50% higher drying performance with films compared to former rotor generations. -Better access; even the preceding dryers already were equipped with hingeable housing covers; the covers of the new generation 1016 and 2016 can even be hinged open on tow sides. A total removal of the housing cover with the help of a fork truck or a crane. - Better anti-wear protection for the screens. -Better anti-wear protection for paddles. Our stan­dard paddles are made of an wear-proof material. For particularly abrasive materials there a re paddles with a welded-on anti-wear protection. - The standard version of our housings (starting with size T 1015) is galvanized, no corrosion problems. -For materials with bad flowing properties there are dryers with forced feeding via screw bunkers. Composed of: 1-Material conveying blower type MFT 55/500 with drive motor 11 kW,cyclone separator with frame 2-Screw conveyor unit. For uniform feeding from dry cleaner L approx. 5000 mm D approx. 300 mm 3-Dry cleaner T 1015 Consists of the cabinet, a rotor, a polygonal screen basket made of stainless steel (unhardened),double, external bearings; replaceable wear plates on the rotor blades. screen basket diameter: 950 mm working length: 1400 mm screen perforation: 2,5 mm Drive: 55,0 kW 4-Platform and steel structure for dry cleaner For the purpose of elevation of the dry cleaner, necessary steel structure with platform and access stair 5-Auxiliary blower Material conveyor blower type MFT 18/180 with drive motor 1,5 kW 6-Discharge screw with rotary valve 315/480 L approx. 4000mm D 150mm

Set of 3 Herbold agglomerators (plastcompactor) working together. Working hours : 19651 1/ Plastcompactor HV 70/250 Storage silo (4cbm) with feeding screw Herbold Plastcompactor, type HV 70/250 Conveying system Herbold granulator, type SML 45/100-S4-2 Conveying system and recycling system for fines Material transport system 2/ Plastcompactor HV 70/250 Storage silo (4m3) with feeding screw Herbold Plastcompactor, type HV 70/250 Conveying system Herbold granulator, type SML 60/100-S4-2 Conveying system and recycling system for fines Material transport system 3/Plastcompactor HV 50/110 Storage silo (4m3) with feeding screw Herbold Plastcompactor type HV 50/110 Conveying system 1 Blending silo type SMV 20000 1 Electrical control, PLC

Crushing of pre-crushed industrial film waste. Material thickness:from 8 to 150 microns. Discharge – directly to friction washer Materials such as stones, metals, rubber, wood, glass, etc. that can damage the crusher are sorted by the customer before being fed into the line. No feeding belt. Constructed to be loaded by a belt conveyor, stable welded structure made of finned steel, with protective curtains to prevent backflow of material. Both fixed blades are mounted oppositely within the dividing support surface. Hydraulic device for automatic opening and closing of the upper mouth Protection against wear and tear Crusher rotor design: open knife rotor, no thread in the rotor, fixing of the knife by means of hexagonal bolts and clamping strips. Change of blades by means of a pulse screwdriver All knives are made of Ch-Ni tool steel. Rotor supports: Self-aligning roller bearings mounted outside the crushing chamber. Knives can be installed and adjusted outside the machine in the supplied mounting device. Scrren replaceable, tool-free mesh change, quick access to the crushing chamber All electrical elements are installed in a rigid sheet steel cabinet. The connection diagram is made as an automatic sensor control; control of buttons with light indicators, main switch closes, terminals connected by wires, including safety elements. The design complies with the current safety regulations of the Association of German Electrical Engineers. The machine is stored indoors. The photos were taken outside for ease of taking pictures.

Pipe crusher for up tp 200 mm pipes Automatic draw-in of pipes and profiles.