Used Anilox and Cylinder washing machines

ATEX PNEUMATIC WASHING TANK The machine cleans inkwells and all its solvent ink tools. Internal measurements : 2400mm long x 650mm wide x 500mm high. Service tank capacity : 200liters Washing solvent level min : 120 Liters Washing pump : 1"1/2 Air consumption Liters/min at 6 bar pressure : 2400 Washing pump capacity : 160l/min Discharge pump : ½". Operating pressure : 6 bar Rinsing time : 10 seconds Ambient working temperature : +5/+40 The PNEUMATIC WASHING TANK has been designed and manufactured for the washing, using solvent, of components/accessories that are part of machines/equipment that during their use get dirty with inks, paints, adhesives, resins, etc. The washing is carried out by means of solvent jets on the components/accessories. After opening the tank lid and positioning the components/accessories on the washing grid, the lid is closed and the washing cycle starts. A pneumatic pump draws the solvent from a containment tank through filters and delivers it in a series of pipes with a pressure of approx. 3-4 bar. These pipes carry the solvent to the washing nozzles positioned near the components/accessories to be washed. The washing is carried out by means of: The mechanical action of the liquid against the part (pressure created by the nozzles); The action of dissolving the dirt generated by the solvent. The dirty washing liquid returns to the containment tank through a discharge pipe. At the end of the washing cycle, the rinsing cycle can be performed (rinsing option) where the pneumatic pump sucks the clean solvent from an external tank to perform the rinsing of the parts removing possible residues from the previous washing. At the end of the washing and/or rinsing cycle, the suction of the gases generated during the washing-rinse can be carried out (suction option). At the end of this phase, the operator can open the washing tank lid and remove the cleaned parts. The time necessary to execute the washing cycle is determined by the quantity of components/accessories to be washed, how dirty they may be and the time during which they have been dirty.

Solvent cleaning system for sale.Includes an exhaust air system. The machine was used to clean the parts of the Nordmeccamica laminating machine. Usable width / height / length: 600 x 300 x 1800 mm Washing pump output: 5 m³/h Internal extraction: 2000 m³/h, 1,1 kW Space required: 4400 x 2700 x 2200

Anilox washing machine “FW 2000 M" Spare parts: hydraulic power pack and various feed hoses. The machine can be washed before sale, as it is covered in places with ink splashes. The machine operates on the following principle: Washing: The anilox is rotated while heated cleaning liquid is sprayed onto its surface for 5 to 15min. The liquid loosens ink particles from the cells and cylinder surface. Liquid recovery : At the end of the wash cycle, the cylinder continues to rotate and the cleaning liquid is recovered and returned to the tank before being filtered and reused. Duration: 2 to 3 min. Rinsing: To remove loose ink particles, the cylinder is rinsed with high-pressure hot water. Nozzles are installed on a rail and slide to rinse the entire surface of the cylinder. Duration: 1 to 2 min. Drying: The cylinder rotates while nozzles blow air over it. The drying nozzles are also mounted on a rail and slide to dry the entire surface of the cylinder. Duration: 1 to 2 min (depending on cylinder length) Max roll length: 1860mm Max roll diameter: 180mm Max roll weight: 2x25kg Max. cleaning length: 1600mm Liquid tank: 55L Options included: Additional tank, filter and pump for additional cleaning fluid Drain tank and pump for rinse water recovery Automatic cleaning fluid refill Operating indicator lamp Interior lamp Set of standard adapters for sleeves.

Sticky plate size : 1220 x 2000 mm

Fully automatic and quick washing process for a large number of rotogravure cylinders. Extremely gentle cleaning process for all types of ink.