Used 10 Colours CI Flexo Printing Machines

Speed up to 500 mt/min Solvent based inks Automatic double unwinder and rewinder for 1000 mm Web guide BST before the printing unit Corona treatment Ferrarini& Benelli Polimetal Thermoregulation unit Frigosystem Automatic pre-register Video System BST One set of anilox and sleeves included (dimension to be discussed)

Installed mid 2015 Earliest Pick up February PRINTABLE MATERIALS ·LDPE, PP 20-200 microns ·HDPE, OPP 12-100 microns ·Laminated films up to 150 microns ·Paper g/m2 30 - 120* ·PET, OPA, BOPP 10-30 microns *Note: When processing paper of up to 120 gsm, the maximum web width can be run only with increased web tension of 450 N. Drying system: Indirect - hot water Designed as a two-circuit recirculating air system for increase of solvent vapour level in exhaust air, type W&H ENPRO Max printing speed: 600m/min Automatic non-stop flying splice shaftless unwinder, Max diameter 1000mm - Central Drive controlled 4 automatic chucks to accept the material rolls for a core of 70mm Chuck adapters for a core of 76mm 2 Pairs of chuck adapters for shaftless unwinder for 150/152mm core 2 Pairs Adaptors for smaller rolls width to reduce the roll width by 400mm Designed for production speed of 600m/min with TESA EASY SPLICE Min web width of 1150mm Roll Lifting Table Automatic non-stop flying splice shaftless rewinder with trim and inline cut (Universal Longitudinal Slitter for a max of 5 cuts ) depending on material prepare Max 1000mm diameter rolls - Central Drive controlled Edge Trim cutting device for the universal slitter to seam the web on both sides for a trim up to 30mm Corematic for automatic roll handling & core loading (3‘&6’' with hotmelt tank gluing) with core magazine El. pneumatic tension control / dancer Web guide before the printing BST Anti-Static rods installed before the first printing deck Single side corona treater AFS without skipping , for non- metallized and metallized films Ink Pumps: 10pcs, Turboclean Advanced E Web Viewing System: AVT ‘ARGUS’ (partial & 100%) 2018 instead of original BST ‘iPQ’ View system Automatic Register, Easyset S & Easyset HD &Easy Reg D. Proof printing system for adjustment of plate cylinders and anilox rolls Web guide prior to rewind Line Scanner for web guiding prior to rewind Viscocontrol:fully automatic viscosity control before and during the printing Integrated in the Turboclean Adv. inking system. Vista-Port change system for the shafts with sleeves. Magazine , to store and prepare plate mandrels and anilox rollers for the next job also during production -23 positions for the plate cylinders and sleeves and anilox rolls -6 sleeves change stations to provide the plate cylinder mandrels with sleeves Web thread-up chain for reverse side web inspection on the drive side. manually operated Procontrol TS ELTAINER Anilox: 29, Apex GTT Sleeves: 5 sets (10x) of sleeve cylinders 440/600/760/920/1080 527 sleeves (560-1110) Power requirement Connected load kVA300 Additional connected load with electric ink pumps KVA 20 Chill water requirement Chill roll (each roll) appr. m3/h1,5 Temperature control unit max. m3/h 4,0 Compressed Air requirement Pressure (above atmosphere) kPa 600

Maximum mechanical speed: 400m/min Turret-type unwinder with automatic changeover Maximum diameter of the reel in unwinder: 1000 mm Reel-holding shafts: 2 x 3" and 2 x 6" SVECOM shafts Turret type rewinder with automatic changeover Reel-holding shafts: 2 x 3" and 2 x 6" shafts SVECOM Reverse printing FIFE Guide PRESS GO - Defect detector Pneumatic pumps SMC 15 Ingersolrand pneumatic agitators GRAFIKONTROL automatic register system Automatic rinsing Automatic viscosity control INSPEK Automatic temperature control In-line cutting Spare parts package available Anilox (only half of the list is included) (Quantity/ LPI(cm)/BCM(cm3)) Praxair and Simec 1/250/9 1/250/10,5 1/100/10,8 1/80/10,5 1/300/10 2/305/10,5 3/120/10,8 2/500/5,8 1/500/4 1/500/6,5 4/700/3 5/800/2,7 2/305/6,5 1/406/6,5 2/508/4,5 2/711/3 4/812/2,7 Sleeves (only half of the list is included) (Z/quantity) Rossini 390/20 400/28 420/18 430/28 440/28 450/32 460/24 470/24 480/16 490/18 500/32 510/8 520/18 530/16 540/20 550/18 560/18 570/16 590/8 600/8 620/18 630/8 640/18 650/10 670/10 700/8 720/8 780/8 800/8 CARRIER/17

Turret automatic unwinder and rewinder. Diam. max reel 1000 mm Videocamera BST with defect and bar code control Corona treatment Web guides FIFE before and after the printing unit Vyscosity control automatic Gama Washing system Anilox 14 pieces from 100 to 450 lines/cm Print Sleeves 20 pieces. 2 sets with development 300-350 at choice

460mpm max speed Print units: 8 units with turner bar & 2 x reverse print units. Closed chamber ink system. Solvent based inks. Unwinding and rewinding: Dual turrets Reel diameter max: 1000 mm Inner core diam.: 76 mm Web tension: 20-500 N Thickness range: Film laminations: 10-120 microns Paper/laminations: max 100g/m2 2020 AVT inspection system, Norcross Visco system Flexpress Auto Clean F&K mandrels available: 380mm – 3 480mm – 10 580mm – 10 680mm – 7 780mm – 10 880mm – 9 980mm – 10 1180mm 10 Sandon aniloxes: 1 x 10.0cm3/m2 -250lpi 3 x 8.0cm3/m2 – 350lpi 1 x 6.0cm3/m2 – 550lpi 3 x 4.2cm3/m2 – 750lpi 2 x 3.6cm3/m2 – 1207lpi & 21 Rotec print sleeves included In constant production since 2004