Used Laminators

Duplex lamination with solvent based and water based adhesives with rotogravure coating system Web width: Max 1350mm, min 420mm Coating width: Max 1325mm Tension range: Unwinder 1: from 20N to 400 N Unwinder 2: from 20N to 400 N Rewinder 1: from 40N to 550 N Taper tension: up to 90% Primary Simplex unwinder, shaftless type (800 series) Max reel diameter: 1020mm (40”) Max reel weight: 1000kg (2200lbs) I.C.D. possibility: 3”-6” (76-152mm) Max cores length: 1350mm (53,1”) Min core length: 420mm (16,5”) Bobst primary unwinder web edge sensor Couple of mechanical chucks for 3” Couple of mechanical chucks for 6” Secundary Simplex unwinder, shaftless type (800 series) Max reel diameter: 1020mm (40”) Max reel weight: 1000kg (2200lbs) I.C.D. possibility: 3”-6” (76-152mm) Max cores length: 1350mm (53,1”) Min core length: 420mm (16,5”) Bobst secondary unwinder web edge sensor Couple of mechanical chucks for 3” Couple of mechanical chucks for 6” Coating unit Drying Tunnel Air recycling system Detecting/control of solvent concentration level Bonding section Thermoregulation for laminating drum Simplex rewinder, shaftless type (800 series) Max reel diameter: 1020mm (40”) Max reel weight: 1000kg (2200lbs) I.C.D. possibility: 3”-6” (76-152mm) Max cores length: 1350mm (53,1”) Min core length: 420mm (16,5”) Couple of mechanical chucks for 6” Viscosity controller, Gama model VIS G30 Rubber roller size: (Rossini) 1.550 2. 590 3. 3610 4. 630 5. 650 6. 670 7. 680 8. 690 9. 710 10. 700 11. 730 12. 750 13. 770 14. 810 15. 820 16. 830 17. 850 18. 910 19. 990 20. 790 21. 1010 22. 1030 23. FULL

Maximum web width:1330 mm Minimum width of web to be laminated: 600 mm Mandrel diameters: · Unwinder: (76 / 152 mm) 3", 6" · Rewinder: (152 mm) 6" Maximum web tension:： · Unwinding: 550 N · Rewinder with taper tension: 600 N · Rewinder with constant tension: 550 N On rewinder taper tension can be adjusted from 10% to 50% of the set figure. Minimum web tension: · Unwinding: 20 N · Rewinding: 40 N Maximum roll weight: 1000 kg Supports to be coated: ALU 6.5 – 40 my BOPP 12 - 80 my LDPE, LLDPE 30 – 200 my NYLON CAST 30 – 80 my OPA 12 – 18 my PETP 10 – 30 my PP CAST 40 – 150 my Paper 40 – 200 gsm Supports to be laminated: ALU 6.5 – 40 my BOPP 12 - 80 my LDPE, LLDPE 20 – 200 my NYLON CAST 20 – 80 my OPA 12 – 18 my PETP 8 – 30 my PP CAST 20 – 150 my VARIOUS COEX 20 – 200 my Bi-2 Mixer

OPP,PET,Cellophane,nylon, CPP,PE etc and aluminum foil and paper. Thickness 7+ microns Roll wide 1150mm Film wide Max 1080mm Dryer heat source is LPG Unwinder shaftless auto splice Rewinder shaft Drive DC motor Modify CPU and vector invertor changed 2007 year Speed Max 200m/min Includes 20-30 Sleeves

Maximum speed = 450 m/min Minimum width = 600mm Maximum material passage width = 1.330mm Maximum width of adhesive application = 1315mm Shaftless on unwinder and rewinder Maximum reel diameter 1000mm Maximum roll weight 1000 kg Dosing system and sleeves included Mixer included Materials to be glued : ALU : 6.35-40 microns BOPP : 12-80 microns LDPE, LLDPE : 30-200 microns Nylon cast : 30-80 microns OPA : 12-18 microns PETP : 10-30 microns PP cast : 40-150 microns Paper : 40-200 gsm Materials to be laminated : ALU : 6.35-40 microns BOPP : 12-80 microns LDPE, LLDPE : 20-200 microns Nylon cast : 20-80 microns OPA : 12-18 microns PETP : 8-30 microns PP Cast : 20-150 microns Various coex : 20-200 microns Paper : 30-200 gsm Sleeves : Length of sleeves x Quantity 852 mm x1 870 mm x1 970 mm x2 1078 mm x1 1083 mm x1 1110 mm x2 1198 mm x2 1202 mm x1

Installed in 2021 Max coating width 1310mm Min. roll width 300 mm Inner core diameter 76,2 mm (3''), (152,4 mm (6'')) Max. reel weight 800 kg Web edge guiding range + 50 mm Water temperature for roller temperature control max. 90°C Provision for installation of corona surface treatment unit - connecting holes Optional accessories included: 1 Primary and secondary unwind unit mechanical clamping cones for 152,4 mm core diameter (4 pcs) - Dural: 1 pair 2- Adhesive coating unit: set of Teflon dams (2 pcs): 3 sets 3- Rewind unit pneumatic shaft for 76 mm diameter cores with carriers (assembly instead of mechanical cones or pneumatic chucks), 1 pc 4- Temperature control system loop for application roller R4 temperature control 1 pc 5- Adhesive evaporation ducting: filter material for ca 60 pcs of collector fillings 1 pc 6- Cooling cylinder: driven cooling cylinder 1 pc 7-Adhesive dosing unit: two-components adhesives dosing and mixing unit bi-2 MINI mixer from co. LR incl. automatic refilling for mixer 1 pc 8- Static plastic mixing element (consumable) will deliver all pieces existing 9- compressor cooling unit for cooling cylinder 1 pc MATERIALS Primary materials for adhesive application: BOPP 0,012 – 0,08 mm PET 0,01 – 0,03 mm PE, LDPE 0,03 – 0,20 mm OPA 0,012 – 0,06 mm CAST PP 0,04 – 0,15 mm CAST PA 0,04 – 0,08 mm ALU FOIL 0,012 – 0,04 mm Possibility of Al-foil processing depends on its quality. PAPER 30 – 150 g/m2 For paper processing, special optional equipment is necessary - one-component adhesive dosing system. LAMINATES up to 150 g/m2 Minimal thickness of PE, LDPE, CAST PP, CAST PA depends on kind of used adhesive. Secondary materials - laminated: BOPP 0,012 – 0,08 mm PET 0,008 – 0,03 mm PE, LDPE 0,02 – 0,20 mm OPA 0,012 – 0,06 mm CAST PP 0,02 – 0,15 mm CAST PA 0,02 – 0,08 mm ALU FOIL 0,009 – 0,04 mm Possibility of Al-foil processing depends on its quality. PAPER 30 – 150 g/m2 For paper processing, special optional equipment is necessary - one-component adhesive dosing system.