Used Offset Printing Machines

Automatic offset machine for printing 2-5 colours on eggs trays. Tray size range Length 250-320 mm Width: 220-225 mm Printing area 120x290 mm Number of the printing colors 2-5 Production capacity 3750-5000 psc/h Printing plate thickness 0,83 mm Expected pressure 6 bar Air supply 6-12 bar Air consumption 500NL/min Pneumatic holes diameters i-9mm, e-12 mm Noise ( near 1 m) max 75 dB Main Engine 2,2 kW Working hours approx 10 000 h The machine includes all equipments needed for production. All machine functions as well as all units controlled by computer. A complete set of rollers for each colors easy for disassemble. Automatic stack loading system with mechanical container distribution system. Automatic chain feeding and transport system. Mechanical device counting the number of pieces at the unloading station.

Printing machine for egg trays + LABEL MACHINE Upper 3-color printing + lacquering on lower barcode Lacquering machine 4-station loading with pick and place handling Single-station stacking unloading with accumulation Package handling by chain with constrained distance porters Production capacity from 4,000 to 6,000 pcs/h

Printing machine for egg trays Upper 3-color printing + lacquering on lower barcode Lacquering machine 4-station loading with pick and place handling Single-station stacking unloading with accumulation Package handling by chain with constrained distance porters Production capacity from 4,000 to 6,000 pcs/h

Printing system for rectangular/square/round cups 8 colors Min/max height: 30-125mm Min-max side of cup: 65x85mm - 135x180mm Max printing height 145mm Max printing length: 417-520mm Min-max angle: 2-10- Max printing speed : up to 9000/h UV curing Cup loading with screw feeder, corona pretreatment for coat and bottom on two stations, transfer, positioning before and after printing and universal discharge Horizontal ink fountains mounted with ink mixers. They allow a better printing quality on screened or solid surfaces. The ink fountains are equipped with a separate drive to facilitate washing and pre-inking.

Maximum taper 15 degrees Maximum print height 120 mm Maximum print length in 4 BLANKET MODE: 340 mm (Ø 108 mm) M Maximum print length in 2 BLANKET MODE: 425 mm (Ø 135 mm) option Maximum mechanical speed 400 products per minute The actual maximum printing speed depends on the cup design. Transformer for Frequency 50 - 60 Hz Connected load 40 kVA Nominal load 32 kVA The basic line configuration includes: •Feeding unit/IN- Feed System. A single lane feeding belt, which transports the products into the feeder tube. Feeder Tube for Belt Feeder Transports the product stacks from belt feeder to the screw feeder •Handling section •Corona Pre-treatment station •Printing section with 6 colour heads •Curing station: Curing on Mandrel, Single UV-lamp system, 6kW curing capacity •Take off / re-stacking unit Extras included: 1- Video Punch and Bending Jig: A tool for punching of mounting holes in the printing plates. The tool uses one camera and monitor for high accurate punching of the mounting holes and guarantees a registration accuracy within 0.07 mm. The plate ends can be accurately bent for precise mounting of the printing plates. 2-Quick Set Ink Fountain with Segmented Knife: A scale to show ink flow through ink knife giving reference point and repeatable settings. Levers are used to adjust the segmented ink knife. 3-Laser Counting Re-stacker: The cups rims are counted when they pass a laser. When the correct number of cups has passed the laser sensor, the stack is pushed forward and rolls onto the collecting table. 4- 2 Blanket Mode (for print lengths > 340 mm): This (electronic) mode changes the drive ratio between the index unit and the print section and enables longer printing lengths up to 425 mm. Hold-on Mechanism . A mechanical hold-on which ensures the product stays on the mandrel during printing (required for special cup types only). 5- Tray Feeder: A-frame tray feeder with width of 950 mm (useful width). 6- EPS In-feed Belt: Conveying Belt up to 10’, actual length TBD above feeder rods under an angle of 45° for stack pressure with 3 sensors (high, medium and low level) to control in-feed speed. 7- Screw Separator: Feeds cups one by one into a special feeding tube (sized to product) with stack level control. Used for non- bending stacks. 8- Air Jet Separator: Feeds cups one by one, by air, into a special feeding tube (sized to product) with stack level control. Used for non-bending stacks. 9- Holder for Rubber Rollers: To store rollers when not in use. 10- Tool Sets 1 set (8) mandrels, shafts, ring for product up to Ø 100 mm 1 set (8) mandrels, shafts, ring for product Ø 100 mm - Ø 160 mm 1 set (8) mandrels, shafts, ring for product Ø 160 mm - Ø 205 mm 1 set of 3 feeder screws (if needed) 1 set (3) special blow pieces 1 special infeed tube with blow pieces for high speed EPS feeding